Most tankless water heater problems come down to a few causes. The unit isn’t getting the power, gas or water flow it needs to fire. It lit and then lost its flame. Scale or a clogged inlet filter is choking it. The vent is blocked. Or it froze. Most units show a code that points to the problem, and some of the checks below are safe to do yourself. Gas, venting and electrical repairs are for a licensed technician.
This guide covers gas and electric tankless water heaters from Rinnai, Navien, Noritz, Rheem and other brands. If you have a standard tank heater, our gas water heater troubleshooting guide is a better fit. For a specific code, our water heater error codes guide lists them by brand.
Stop First If You Smell Gas
- Leave the building now. Don’t light anything, flip a light switch, unplug the heater or use a phone inside.
- Call from outside or from a neighbor’s phone: 911 or your gas utility’s emergency line:
- Puget Sound Energy (WA)1-888-225-5773
- NW Natural (OR, SW WA)1-800-882-3377
- PG&E (Northern CA)1-877-660-6789
- SoCalGas (Southern CA)1-800-427-2200
- Stay out until the utility or fire department says it is safe.
Carbon monoxide: headache, dizziness, weakness, nausea, sleepiness or confusion while the heater is running can be signs of CO. Get outside to fresh air and call 911. The CPSC recommends a CO alarm on every level of the home and outside sleeping areas.
Quick Symptom Lookup
Find your symptom below and jump to that section.
| What you see | Most likely cause | Safe to try yourself? |
|---|---|---|
| No hot water at all | No power, gas valve closed, ignition failure or blocked vent | Yes: check power, the gas valve and the code on the display |
| Hot in the shower, cold at the sink | Flow is below the unit’s minimum to fire | Yes: open the hot tap fully and clean the aerator |
| Hot, then a burst of cold | The “cold water sandwich” from quick on/off use | Usually normal; a buffer tank or recirculation fixes it |
| Never hot enough | Too many fixtures at once, low setting, scale or a clogged filter | Yes: check the setting and clean the inlet filter |
| Error code on the display | The unit is reporting what failed | Look it up below, then reset once |
| LC or E760 code | Scale buildup or a flush reminder | Flush or descale the unit |
| Water leaking from the unit | A fitting, the relief valve, the condensate line or a cracked heat exchanger | Shut off water and power, then call |
| Stopped after a freeze or outage | Freeze protection needs power; a frozen unit can crack | Check for leaks before restoring power; call if you find any |
Step 1: Check Power, Gas and Water
Check these three things first.
Power
Gas tankless units still need electricity for the controls, fan and igniter. A blank display usually means the unit is unplugged or the breaker has tripped. Rinnai notes its units won’t run at all during a power outage.
Gas
The gas shutoff next to the unit should be open, with the handle in line with the pipe. If your stove or furnace is out too, the problem is the gas supply, not the heater. On propane, check the tank level.
Water
Both isolation valves under the unit should be fully open. If the unit was flushed recently, one may have been left closed.
If anything here conflicts with your owner’s manual or the code on your display, go with the manual.
No Hot Water at All
If power, gas and water are all on and the water is still cold, the unit is either not lighting or losing its flame after it lights. The display will usually show one of these codes.
The burner won’t light
Rinnai 11, Navien E003, Noritz 11, Rheem A011. Usual causes are a closed gas valve, an empty propane tank, or a dirty igniter or flame rod.
It lights, then goes out
Rinnai 12, Navien E012, Noritz 12, Rheem A012. Low gas pressure is the usual suspect, especially when other gas appliances are running or the gas line is too small for the unit. Navien also lists a dirty air intake filter.
The vent is blocked
Rinnai 10, Navien E110. Check the vent caps outside for snow, leaves, a nest, or anything stacked against them. Clearing debris is fine; opening or changing the vent pipe is not.
Turning the unit off and back on clears most codes. If the same ignition or flame code comes back, stop there and call. Repeated failures can lock the unit out, and gas pressure, gas line sizing and venting are not DIY repairs.
Hot in the Shower, Cold at the Sink
A tankless heater only fires when enough water is moving through it. Rinnai needs 0.4 to 0.6 gallons per minute to light and shuts off below about 0.26 GPM. Navien, Noritz and Rheem’s IKONIC line need 0.4 to 0.5 GPM. A bathroom faucet opened partway, or one with a low-flow aerator, may never reach that.
Open the hot tap all the way with no cold mixed in. If the water heats up, flow was the problem.
Unscrew the faucet aerator and rinse out any grit.
Clean the inlet water filter on the unit. A clogged screen cuts flow to every fixture.
Try a slightly lower temperature setting. Rinnai notes this helps at low flow because you end up opening the hot tap further.
If one fixture runs cold no matter how far you open it, the cause may be a faulty mixing valve or hot and cold lines that are cross-connected. Navien’s manual lists cross-plumbing as a check. That one needs a plumber.
Hot, Then a Burst of Cold
You shut the shower off for a minute, turn it back on, and get hot water, then a few seconds of cold, then hot again. This is called the cold water sandwich. The hot water left in the pipe comes out first, followed by cold water that passed through while the burner relit, and then fresh hot water. It’s common with tankless units and doesn’t mean yours is failing.
If it bothers you, a small buffer tank or a recirculation system solves it. Navien’s NPE-A2 models build both in.
Water Never Gets Hot Enough
Too much demand at once
Every unit has a limit on how many gallons per minute it can heat. Two showers and a dishwasher can push past it, especially in winter when the incoming water is colder.
The temperature setting
Check the controller. Someone may have turned it down. 120°F is a common setting, and the CPSC recommends it to reduce scalding risk.
Scale or a clogged filter
Scale on the heat exchanger and debris in the inlet filter both cut performance. Navien’s manual lists both as causes of its E016 overheating code. See flushing below.
An undersized unit or gas line
If the problem has been there since installation, the unit or the gas line feeding it may be too small for your home. Noritz code 90 can mean the unit couldn’t reach the set temperature because gas pressure was too low.
Most Common Tankless Error Codes
Codes vary by brand and model. These are the most common. For the full list, see our water heater error codes guide.
| Problem | Rinnai | Navien | Noritz | Rheem (IKONIC) |
|---|---|---|---|---|
| No ignition | 11 | E003 | 11 | A011 |
| Flame lost | 12 | E012 | 12 | A012 |
| Vent or air blockage | 10 | E110 | — | — |
| Overheating | 14, 16 | E016, E030 | — | A014 |
| Didn’t reach set temperature | — | — | 90 | — |
| Scale or flush reminder | LC (LC0–LC9) | E760 | — | — |
Rinnai’s service guide says code 14 “should be taken seriously,” and Rheem links A014 to gas supply or venting problems. Don’t keep resetting an overheating code; call for service.
Scale, Flushing and the LC Code
Every tankless unit slowly collects mineral scale inside its heat exchanger. Left alone, scale cuts hot water output, makes the burner work harder and can trigger overheating codes. Both Rinnai and Navien call for regular flushing:
- Rinnai: flush at least once a year. An LC code on the display means scale is building up.
- Navien: descale at least once a year, and more often with hard water, high temperature settings or heavy use. E760 is Navien’s flush reminder, shown when the service interval set on the unit runs out.
How a flush works
Turn off power and gas to the unit and close the cold and hot isolation valves underneath.
Put a small submersible pump in a bucket of cleaning solution. Run one hose from the pump to the cold-side service port and another from the hot-side port back to the bucket.
Open the service ports and let the solution circulate for about 45 minutes. Rinnai calls for about 4 gallons of undiluted white vinegar and says not to use chemical cleaners. Navien allows white vinegar or an approved descaler.
Rinse with clean water, clean the inlet filter, close the service ports, open the isolation valves and turn gas and power back on.
Navien says skipping the maintenance in its manual may void the limited warranty, and Rinnai recommends having a professional handle the flush. Our tankless maintenance service includes flushing out sediment and scale and checking the system for leaks. For more ways to keep a unit running, see 4 steps to extend your tankless water heater’s lifespan.
Clean the Inlet Water Filter
Most tankless units have a small screen filter where the cold water comes in. When it clogs, flow drops and the unit can shut off or run lukewarm. The DOE Building America Solution Center suggests cleaning it every 6 to 12 months. Most homeowners can handle this one.
Turn off power and gas, close the cold water inlet valve and open a hot tap to relieve the pressure.
Unscrew the filter, rinse it under running water and brush off any debris.
Reinstall it, open the valve, check for drips and turn gas and power back on.
Some units also have an air intake filter. Navien suggests cleaning it every 3 to 4 months.
Water Leaking From the Unit
First, shut off the water supply and power to the unit. Then find where the water is coming from.
Fittings and valves
Drips at the isolation valves, service ports or filter cap often show up after a flush. A loose cap or worn washer is usually a simple fix.
The relief valve
Water from the pressure relief valve line can mean high pressure or overheating. Never cap or plug it. Call for service.
The condensate line
Condensing units produce acidic condensate that drains through a line, often through a neutralizer. A clogged line or trap can back up. On Rinnai units, code 25 is a condensate trap error.
Inside the cabinet
Water inside the unit, especially after a freeze, can mean a cracked heat exchanger or internal pipe. That needs a technician.
Freezing and Power Outages
Tankless units have built-in freeze protection, but it only works while the unit has power. Rinnai says to keep power on continuously, and Navien’s installation manual says freeze damage isn’t covered by its warranty.
- Keep it plugged in all winter. Navien’s manual says not to unplug the unit except for routine maintenance.
- During a long outage in freezing weather, Rinnai and Navien both say to drain the unit. Rheem also mentions leaving a small stream of hot water running.
- After a freeze, check for water on the floor or inside the cabinet before restoring power. If you find any, call for service.
Electric Tankless Water Heaters
Electric units have no burner or venting, so problems are usually electrical or flow-related.
Tripped breakers
Whole-house electric units run on several double-pole breakers. Stiebel Eltron’s Tempra manual lists two or three 50-amp breakers, depending on the model. Check every one.
Won’t turn on
Like gas units, electric models need a minimum flow, about 0.5 GPM on the Tempra. A clogged inlet screen can keep them from switching on.
Safety cutout keeps tripping
A thermal cutout that trips again and again points to a fault that needs service.
Failed heating elements
Elements can fail from air pockets, scale or freezing. Testing and replacing them means working with high voltage, so leave it to an electrician or technician.
When to Call a Pro
- You smell gas or suspect carbon monoxide. Leave first, then call (see the top of this page).
- The same ignition, flame or overheating code returns after one reset.
- The fix involves gas pressure, gas line sizing, venting or the condensate system.
- There’s water inside the cabinet, or a leak you can’t trace to a fitting.
- An electric unit needs electrical testing.
Repair or Replace?
Usually worth repairing
An igniter, flame rod, sensor, fan or circuit board on a unit that’s otherwise in good shape.
Time to replace
A cracked or badly scaled heat exchanger on an older unit. ENERGY STAR puts tankless life expectancy at 20 years, so a major repair near that age is rarely worth it. Compare options on our tankless water heaters page.
Tankless Acting Up? We Can Help Today
Fast Water Heater Co. has been repairing, flushing and installing tankless water heaters across Washington, Oregon and California since 1986, including Rinnai, Navien, Noritz and Rheem. Call by noon for same-day tankless repair and maintenance in most areas. Free estimates, no trip fees.
Tankless Water Heater Troubleshooting FAQ
Why is my tankless water heater not producing hot water?
The most common causes are no power to the unit, a closed gas valve or empty propane tank, water flow below the unit’s minimum, a clogged inlet filter, or an ignition or flame failure. Check the display for an error code, make sure power, gas and water are on, and open the hot tap all the way.
How do I reset my tankless water heater?
On most units, turn the controller off and back on, or switch off power at the plug or breaker for a minute. That clears most codes. If the same code comes back, don’t keep resetting it. Have the unit serviced.
How often should a tankless water heater be flushed?
Rinnai and Navien both recommend at least once a year, and Navien says more often with hard water, high temperature settings or heavy use. Rinnai units show an LC code when scale is building up.
Why does my tankless water heater go hot, then cold, then hot?
That’s the “cold water sandwich”: hot water left in the pipe, then cold water that passed through while the burner relit, then fresh hot water. It’s common with quick on/off use. A buffer tank or recirculation system reduces it.
How long do tankless water heaters last?
ENERGY STAR puts tankless life expectancy at 20 years, longer than any conventional tank water heater. Regular flushing helps a unit get there.
Sources
- Rinnai: Tankless water heater FAQ
- Rinnai TB-075: Condensing water heater error codes
- Rinnai: Flushing your tankless water heater
- Rinnai: Freeze protection
- Navien NPE-2 user’s information manual
- Navien NPE installation manual
- Navien: How to descale a tankless water heater
- Navien NPE-A2 series
- Noritz: Common tankless error codes
- Rheem IKONIC service pocket guide
- Stiebel Eltron Tempra installation manual
- DOE Building America Solution Center: Clean a tankless water heater filter
- ENERGY STAR: Gas tankless water heater benefits
- ENERGY STAR: When should you replace your water heater?
- CPSC Carbon Monoxide Information Center
- CPSC: Tap water scalds
- Gas leak safety: Puget Sound Energy
- Gas leak safety: NW Natural
- Gas leak safety: PG&E
- Gas leak safety: SoCalGas
Last reviewed November 2026.